Janine Broussard спросил 5 месяцев назад
How to Replace a Kia Sportage Replacement Key
For a variety of kia sportage key replacement models, the key contains a keyless entry system built-in. The key can be compared to the remote control and can be replaced with a fresh one from a Kia dealer or locksmith.
Key fobs can stop working for several reasons, including the battery of the coin is dead, worn buttons signals, water damage, signal interference and a malfunctioning receiver module. Here are some suggestions to help you get your Kia sportage replacement key working once more.
How to replace a remote key or smartkey
Whether your Kia is equipped with an intelligent key, remote key push-to-start key, or a regular non-transponder metal key, the battery in these keys will eventually require replacement kia keys. This is particularly true if your car displays a message that indicates the smart or remote keys have low battery power.
It’s an easy procedure. In order to replace the battery on the key fob take out the mechanical key from the slit at the back of the key fob. Then break the cover. A small screw will be found inside the key fob, which holds the battery in the correct position. Take out the old battery by unwinding the screw with a small screwdriver. Install the new battery and close the gap on the key fob.
When the key fob is equipped with a fresh battery Test it by pressing the locks and unlock buttons. It’s okay in case the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become cold or when you need to do some errands in Brandon.
Note: Certain key fobs could need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or automotive locksmith can access. Other keys (non-transponder metal keys) don’t require programming. If you’re required to reprogramme your key, it is necessary to write down the key code’s number on the key code tag.
How do I replace the battery?
If the Kia key fob doesn’t respond when you press the lock/unlock button, it’s a sign that the battery is depleted. A battery that is not functioning properly can cause other issues, such as the check engine light appearing or the engine not cranking correctly. Fortunately, replacing the key fob battery is a relatively simple DIY task that requires only some basic tools.
Before beginning the process ensure that your vehicle is turned off and that all doors are closed. Locate the small plastic piece on the bottom of your key fob and play with it until a metallic key slips out. Then, you can insert this key into the driver’s door handle to unlock your car.
To replace the battery inside the key fob remove the rear cover. Use a pry tool to remove the latch that holds the black negative cable. Remove the old battery and then orient the new one in a way that the «+» positive side is facing you, while the «-» negative side is facing towards the fob’s metal electrical contacts. Push the new CR2032 battery straight into place and avoid excessive force to avoid bending or damaging the metal contacts.
After installing the new battery after which you turn the key fob on and off in the ignition until the door locks cycle. Then you can test your kia sorento key key fob and see whether it’s functioning properly again.
How do I replace a smart keys
You may have either the standard keyfob or Smart Key based on the model of Kia Sportage. The smart key is equipped with an embedded mechanical key blade, while the standard keyfob does not. Both key fobs contain batteries that eventually require replacing. It’s an easy task that will take about two minutes.
Before you start it is important to make sure that you are on a level surface with enough lighting and that your Kia is not on. Keep in mind that the fob has tiny parts that could fall in the event of a mishap.
The small release button is located on the lower backside. It’s either a circular button or rectangular slot. You can open the key fob by pressing the button.
Once you have the key fob opened it is easy to remove the old battery, and replace it. The new battery is C2032, and can be bought through the internet or at a local auto parts shop. After you’ve finished, your key fob should be able to lock or unlock and start your vehicle, even if it isn’t running.
How to replace a mechanical key
The Kia key fob is a fantastic option that lets us lock and unlock our vehicle with the touch of one button. However, like all devices it will encounter issues from time to time. There are ways to address these issues and keep your key fobs working for many years.
A low or dead battery is among the most common problems. This could cause your device to stop working or operate intermittently. If this is the case try replacing the battery with a fresh new one.
If this doesn’t solve the problem, use the flathead screwdriver that is standard to push the fob’s plastic casing open. Be careful not to harm any internal components or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a brand new one.
Close and open the door using the mechanical key. (Every kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob to confirm it’s functioning properly. If the fob still isn’t functioning, contact a dealer or locksmith to solve the issue. To avoid a lockout in the future ensure you purchase an emergency key that will be able to work with all door and trunk cylinders.